Lubrication Greases
1. Rolling and Sliding Bearing Greases
1.1. for High Pressures
Greases with MoS2 are for heavy duty greasing points and long-term greasing with emergency run properties. MoS2 prevents contact of the sliding surfaces, particular in the boundary lubrication range. MOLYDUVAL greases with MoS2 are a valuable supplement for higher pressure, extreme temperatures and for use in contact areas where a hydrodynamic film cannot be formed.
|
Mona-Lisa |
||
|
Multi-purpose heavy duty grease for high loaded greasing points and for long-term lubrication with emergency-run properties, absolutely water-resistant, good friction coefficient |
• for building equipment like dredges, cranes, rollers, mixers, cement industry, sugar mills, mills, machinery factory |
-25°C up to +130°C, shortly +150°C |
|
Mona-Lisa 1000 |
||
|
Special type of MOLYDUVAL Mona-Lisa with high base fluid viscosity, very tacky, for slow motion bearings under highest pressure |
• same application as Mona-Lisa |
-25°C up to +130°C, shortly +150°C |
|
Pegasus C 46 |
||
|
High-temperature MoS2-grease with very good water resistance. Good long-term stability, provide excellent load carrying and rust protection over a wide temperature range. |
• for rolling bearings and slide bearings at high temperatures |
-20°C up to +160°C, shortly +200°C |
|
Duventon |
||
|
High temperature, non melting grease for heavy duty greasing points e.g. in hot air stream and in radiation heat. Resistant to hot and cold water, steam, acids and lye’s. Due to the fact that it is extremely resistant to ageing it is especially fitted for those lubricating points which are accessible with much difficulties. No getting dirty of the goods by dropping grease; Lubrication, even under critical lubrication conditions. |
• For all hot lubrication points |
-30°C up to +180°C, shortly +200°C
|
|
Aero 50 |
||
|
Permanent lubrication at extremely low temperatures or strong temperature fluctuations, especially at high pressures. |
• for airports and airport equipment |
-55°C up to +100°C |
|
Long-Life |
||
|
Light-Colour EP grease for long-term greasing under maximum load, good adhesion, absolutely water-resistant, even against boiling salt water and sea water, best corrosion protection, prevents rust, good sealing. |
• for industrial equipment, motor vehicles, construction equipment and agricultural equipment, for heavy duty and in dusty and moist surroundings. |
-30°C up to +120°C, shortly +130°C |
|
Long-Life PIT17 |
||
|
Similar to Long-Life but more tacky. Good adhesion, absolutely sea water-resistant, very good sealing. |
• Same as Long-Life |
-30°C up to +120°C, shortly +130°C |
|
Long-Life T 2 |
||
|
Light colour heavy duty grease with low friction coefficient, better protection against tribocorrosion. Contains PTFE as a solid and friction modifier. Absolutely water-resistant, even against boiling salt water and sea water, best corrosion protection, prevents rust, good sealing. Offers Emergency Lubrication. |
• for industrial equipment, motor vehicles, construction equipment and agricultural equipment, for heavy duty and in dusty and moist surroundings. |
-30°C up to +120°C, shortly +130°C |
|
Long-Life Z 2 |
||
|
White coloured, heavy duty grease with an added synergetic combination of white solid lubricants. |
• Same as Long-Life T 2, but more white and a little bit cheaper |
-30°C up to +120°C, shortly +130°C |
|
Pegasus C 6 |
||
|
Special high-temperature grease with excellent water resistance, high dropping point, heavy-duty capacity, no deposit formation in the highest temperatures. |
• for slide and roller bearings, even under heavy conditions, under high temperature and especially in humid air |
-20°C up to +180°C, shortly +200°C |
|
Bariplex |
||
|
Very tacky, sea water resistant shippers grease for the points of lubrication, where water is present, extremely water resistant and adhesive. |
• for slideways and slide bearings, where frequent or continuous water contact may occur |
-20°C up to +170°C |
|
Valenzia |
||
|
High-temperature grease on complex base in a very wide application range, very strong extreme-pressure properties, good adhesion, extremely water resistant. |
• For the lubrication of high speed bearings under high temperature and under heavy load even for long-life and lifetime lubrication |
-35°C up to +170°C / +200°C |
|
Valenzia Z 2 |
||
|
Same as Valenzia, but with added PTFE, white coloured, lower friction, better wear protection |
• Same as Valenzia |
-35°C up to +170°C / +200°C |
|
Pegasus C 6 |
||
|
Special high-temperature greasewith excellent water resistance, high dropping point, heavy-duty capacity, no deposit formation in the highest temperatures. |
• for slide and roller bearings, even under heavy conditions, under high temperature and especially in humid air |
-20°C up to +180°C / +200°C |
|
Pegasus C 46 |
||
|
High-temperature MoS2-grease with very good walkstability, provide excellent load carrying and rust protection over a wide temperatures. Provides a very low coefficient of friction because its high solid lubricant content. |
• for rolling bearings and slide bearings at very high temperatures |
-20°C up to +180°C / +200°C |
|
Pegasus KLE |
||
|
High temperature grease with low evaporation. For long-term lubrication without residue. Leaves no carbon residue. Resistant to age |
• for slow and fast running bearings at high temperatures, ventilator bearing, electric motor bearings, coupling pressure bearings. |
-40°C up to +180°C / +220°C |
|
Pegasus KPA |
||
|
High temperature grease with extremely low evaporation. For long-term lubrication at high load and at very high temperatures. Leaves no carbon residue provides excellent protection against corrosion, resistant to age. |
• for roller bearings, gears, chains, ovens chain grates etc. |
-40°C up to +150°C, / 220°C |
|
Pegasus GBE 54 |
||
|
Light brown coloured high temperature grease with extremely low evaporation (at 230°C only 3.5%). For long-term lubrication at high load and at very high temperatures. Leaves no carbon residue provides excellent protection against corrosion, resistant to age |
• for roller bearings, gears, chains, ovens chain grates etc. |
-40°C up to +230°C NLGI 2 for central lubrication systems use Pegasus GBE 54-0 |
|
Pegasus KD 460 |
||
|
Highest temperature grease based on fluorinated oils with PTFE. For long-term lubrication at highest temperatures (up to +300°C). |
• for roller bearings, gears, chains, ovens chain grates etc. |
-15°C up to +290°C, shortly above 300°C NLGI 2 |
|
Aero 75 |
||
|
Synthetic long life lubrication at extremely low temperatures and under strong fluctuations of the temperature. |
• for airport equipment |
-70°C up to +150°C |
|
Aero 92 |
||
|
Modern, synthetic, PAO based low temperature grease. Very good plastics compatible. |
• For low temperature rolling bearings of all kind |
-60ºC up to +150ºC |
|
Aero 55 |
||
|
Low temperature grease for temperatures up to minus 55°C, very long time stable. |
|
-55ºC up to +80ºC |
|
Aero 50 |
||
|
Same as AERO 55 but added with purest MoS2 |
|
-55ºC up to +80ºC |
|
Supravit 14 CM |
||
|
Light Colour grease for high speed rolling and sliding bearings. Offers at normal pressures, very good wear protection, water resistance good corrosion prevention |
• for rolling and sliding bearings at high revolutions |
-50°C up to +105°C |
|
Supravit 75 LS |
||
|
Synthetic grease for high speed rolling and sliding bearings. For high pressures:, very good wear protection, long-life lubrication, water resistance, good corrosion prevention, no deposits and no gelling. |
• for rolling and sliding bearings at high revolutions and high pressures, also at very different working temperatures |
-54°C up to +150°C |
|
Supravit 92 LP |
||
|
Modern, high speed grease based on PAO, for all kind of bearings, very plastics compatible. |
• for bearings with high revolutions also at very high temperatures |
|
2. Gear Greases
Flow greases with MoS2 are for heavy duty gears and offer emergency run properties. MoS2 prevents contact of the tooth surfaces, particular in the boundary lubrication range. MOLYDUVAL Flow Greases with MoS2 are a valuable supplement for higher pressure, extreme temperatures and for use in contact areas where a hydrodynamic film cannot be formed.
|
MOLYDUVAL |
Properties |
Applications |
Datas |
|
Prometheus L |
Tacky standard grease for gears under normal loads. Water resistant. |
• for gears under standard load |
-20°C up to +100°C available in NLGI 0, 00, 000 |
|
Prometheus MA |
Tacky special grease for gears under highest loads. Water resistant. Added with heavy duty solids. |
• for gears under highest load |
-20°C up to +100°C |
|
Prometheus MC |
Synthetic high viscosity, tacky, gear-flow grease with MoS2 for lubrication of heavy duty, slow running gears with bath lubrication. |
• For extremely high loaded gears • for lubrication of slow running gears • for lubrication of chains in special difficult cases |
-10°C up to +185°C |
|
Prometheus BG 290 |
Special tacky grease for slow running, mostly large, open gears under highest loads and very high temperatures. Water resistant. Mostly applied by mist lubrication, available in different consistency classes. |
• for gears under highest load and highest temperatures, as gears at mills |
-30°C up to +250°C |
|
Prometheus OZ |
Open gear and cog-wheel lubricant for high loaded open gears and turnstiles. Prevents the gears from galling, welding and excessive wear, even under heavy load and at boundary lubrication conditions (dusty or rough weather). Prometheus OZ contains purest MoS2 powder in a viscous, tacky and very adhesive base. After evaporation of the solvent a plastisized film with good adhesion remains. |
• for construction machinery, cranes, dredges, building equipment, breakers |
-25°C up to +80°C Semifluid, tacky Carrier Mineral Oil Even available as Spray: |
3. Chain Greases
|
Sekorex PLX |
||
|
Very adhesive heavy duty chain flow grease with MoS2 diluted in hydrocarbons for high loaded chains, extremely water repellent, corrosion-proof, applicable under corrosive conditions, a honey-like sticky film remains which is not thrown off. Very good creeping properties, extremely water-repellent and age resistant. |
• for triple chains in building equipment |
-25°C up to +170°C Viscosity, 40°C: 3000 mm²/s Carrier Synthetic Oil Even available as Spray: |
|
Sekorex D 26-00 |
||
|
Synthetic Chain Grease for Long-term Lubrication, biodegradable |
• chains in fork lift trucks, mills and textile machines |
-30°C up to +130°C / 150ºC Carrier Synthetic Ester |
4. Food Grade Greases
All greases described herein are Food Grade, means USDA H1
See also our special catalogue "MOLYDUVAL LUBRICANTS FOR FOOD INDUSTRY"
|
Soraja C 302 |
||
|
Transparent, universal, adhesive, very water resistant grease for lubrication in food industry. Based on Calcium thickener and for this with best water resistance of all thickeners. |
• for lubrication of rolling bearings in the food industry |
-20°C up to 150°C, shortly +180°C NLGI2 |
|
Soraja C 402 |
||
|
Transparent grease for lubrication of bearings, valves and taps. Very tacky. Strong adhesiveness. MOLYDUVAL Soraja C402 is a long-life lubricant with excellent adhesive properties. |
• for lubrication of sliding surfaces in food industry |
-35°C up to 160°C, shortly +200°C |
|
Soraja C 532 |
||
|
Transparent, universal, adhesive, water resistant grease for lubrication in food industry. |
• for lubrication of rolling bearings in the food industry |
-20°C up to 150°C, shortly +180°C NLGI 2 |
|
Soraja B 100 |
||
|
Transparent low temperature grease for bearings in cold areas |
• for lubrication of rolling & sliding bearings until –50ºC |
-52°C up to 120°C |
|
Soraja B 202 |
||
|
Transparent high temperature grease for bearings until 200ºC and higher |
• for lubrication of rolling & sliding bearings until 200ºC |
-20°C up to 200°C / 220ºC |
|
Soraja T 2 |
||
|
Same as Soraja C 532, but with added PTFE, white coloured, offers lower friction and emergency lubrication |
• same applications than Soraja C 532 |
-20°C up to 150°C / +180°C NLGI 2 |
|
Prometheus A 00 LM |
||
|
White colour adhesive gear grease for all kind of gears with grease lubrication in food industry. Based on special very oxidation and temperature stable PAO's with FDA / USDA H 1 clearance. |
• for lubrication of gears in food industry |
-30°C up to 150°C NLGI 00 Synthetic Oil (PAO) Based
|
5. Silicone Greases
|
Siligra GO |
||
|
Special silicone based greases (also named pastes), very good isolation behaviour, wide temperatures, good resistance, good moisture resistance, corrosion proofed |
• for handling of insulators and controllers |
-40°C up to +220°C Consistency ca NLGI 4 Silicone Oil Based |
|
Siligra GI |
||
|
as MOLYDUVAL Siligra GO, but lighter |
• same as Siligra GO |
-40°C up to +220°C |
|
Siligra GU |
||
|
as MOLYDUVAL Siligra GO, but stronger |
• same as Siligra GO |
-40°C up to +220°C |
|
Siligra C 45 |
||
|
Silicone Grease for very high temperatures. |
• for high temperature roller bearings as in ovens. |
-30°C up to +250°C / +300°C |
|
Siligra C 47 |
||
|
A black brilliant grease with solid lubricant additives. Suitable for use at very high temperatures but small pressures |
• for rolling bearings in textile industry (spinning machinery) |
-40°C up to +250°C / +300°C |
|
Siligra C 39 |
||
|
Very deep-temperature silicone grease with wide temperatures., very good corrosion prevention even in wet conditions. |
• for rolling and sliding bearings in deep temperature equipment, as electrical signals, instruments for airplanes |
-70°C up to +160°C / +200°C |
|
Siligra C 57 |
||
|
Special silicone grease for plastic lubrication i.e. rolling bearings. |
• for rolling bearings in ventilators, high-speed electric motors |
-30°C up to +180°C, / +200°C |
6. Contact Greases
|
Contactin CU |
||
|
Contact (switch gear) grease on the base of copper, prevents sparks, decreases burning-surfaces at contacts, reduces friction at sliding contacts, stable against humidity |
• for electrical contacts in interrupters, relays, and mechanical controllers |
|
|
Contactin AL |
||
|
with added aluminium powder |
|
|
|
Contactin AG |
||
|
with added electrochemical silver powder |
|
|
|
Contactin G |
||
|
with a combination of very good conducting metals |
|
|
|
Contactin AY |
||
|
Synthetic contact grease without any solids. Very low friction for easy going electrical contacts.. Also for precision engineering. |
|
|
7. Greases for Precision Engineering
|
Promicron LD 350 |
||
|
The synthetic very tacky grease for long-life and maintenance-free lubrication in a wide temperatures. It's an extreme pressure grease suitable for instruments, bearings and small gear boxes., low oxidation range, no deposits, soft for ease of application, excellent resistance to moisture; prevents rust, tackiness insures noise and vibration damping, good EP qualities, prevents wear |
• for lubrication of small gear boxes and small open gears |
-40°C up to +120°C Consistency NLGI 1 |
|
Promicron YE 320 |
||
|
A synthetic grease for maintenance-free lubrication of air-craft instruments and small precision-bearings at high temperatures and high pressure ! Gives smooth feel to automatic devices., inhibits noise and vibration, long-life properties, a permanent lubricant, protects against wear and moisture, no deposits, non-drying |
• for lubrication of automatic devices and instruments such as air-craft instruments and controllers, tuners, (potentiometers, optical instruments, push-pull-controls) |
-70°C up to +120°C / +150°C Consistency NLGI 2 Promicron LD 350 M same as Promicron LD 350, but added with pure MoS2 Promicron LD 350 T same as Promicron LD 350, but added with PTFE |
8. Biodegradable Greases
Many other lubricants available. See also our special catalogue "MOLYDUVAL Biodegradable Lubricants”.
|
Rabilub |
||
|
Lubricating grease based on the natural rape-oil, no pollution of the environment, biological decomposition, adhesive, work-stable. for lubrication points, where running-out grease couldn't be removed e.g. at chains, gears especially in the agriculture |
• For sliding points |
-25°C up to +90°C, / +100°C Consistency NLGI 2 |
|
Rabilub EP |
||
|
Synthetic, biodegradable greases based on synthetic esters and therefore with much better oxidation stability and lubrication effectiveness than Rabilub 2 or 3 |
• For rolling and sliding bearings |
-30°C up to +120°C, / +130°C |
9. Plastics Compatible Greases (Silicone Free)
|
Polypan PA |
||
|
These new multi-purpose greases are excellent for a wide variety of applications where plastic compatibility is required. Polypan PA combines the characteristics of protection, wear prevention and temperature stability of a synthetic grease with the seal and plastic compatibility of silicone greases. |
• for sliding and rolling bearings, anti-friction bearings of all kind |
-40°C up to +150°C / +200°C |
10. Oxygen Compatible Greases
|
Attila KDO |
||
|
Special grease resistant to oxidising Can be used in presence of oxygen and fuming nitric acid. Remains unaffected. Proofed by BAM as a lubricant for oxygen working until 80 bar at 60°C |
• for sealing in case of oxygen. as for flat seals, cocks, taps, O-rings, glass and metal. |
|
11. Gasoline and Solvent Resistant Greases
|
Attila G 82 N |
||
|
Solvent, Fuel, and Gasoline Resistant Grease for sealing and lubricating special lubrication points. Resistant against most common used solvents and fuels, and against mineral oil, gas, water, and most of the chlorinated solvents too. The contained tackiness prevents, respectively removes vibrations and noises |
• For lubrication of bearings, if they can contact fuel, gasoline, solvents, or their vapour. Fe. ventilation bearings, pump bearings, chain bearings or other in chemical industry, bearings in lacquer, varnish or cleaning industry etc. |
|
|
Attila KD |
||
|
Special grease resistant to oxidising and chemical media. It does not have a melting point and is resistant to heat, since the base fluid is extremely stable as regards oxidation. Remains unaffected in the presence of all types of polar and not polar organic solvents. |
• for sealing in case of chemicals as for flat seals, cocks, taps, O-rings, glass and metal. |
|










